Advanced user manual for Andy pettitte's vr headset 小派vr头盔高级使用手册2020.4.25

Advanced user manual for Andy pettitte's vr headset 小派vr头盔高级使用手册2020.4.25
0

Advanced user manual for Andy pettitte’s vr headset 2020.4.25
First, reduce the whiteness of dark scenes and adjust the contrast and brightness
1, only choose 1 for contrast, -3-2-1 for brightness, or -1 for brightness if it’s too black. Select the right application and restart the helmet

Two, the picture does not overlap, display abnormal, need to open parallel projection

  1. Check “compatible with parallel projection”, adjust and select a small Angle of view, and restart the helmet
  2. Pay attention to the parallel projection of the maximum Angle of view, which greatly affects the picture quality, while the small Angle of view has no effect. Do not use parallel projection normally
    2

Three, the helmet can not identify, but the handle can identify, how to do?

  1. Hold the helmet and shake it repeatedly and sharply between the two base stations for about 15 seconds
    2, helmet lost signal during the game, you can also use this method, the game progress will not be lost
    Four, the helmet completely can not identify, the handle can not identify, how to do?
  2. Directly uninstall pitool, close 360, and reinstall pitool. Normally, it will return to normal immediately
  3. If it still doesn’t work after reloading, restart the computer and repeat step 1
    Five, the picture appears distortion, caton, even drag shadow, how to do?
  4. If the above problems occur, it means that the game is poorly optimized, or the graphics card configuration is insufficient, or the super sampling is too high. You can choose to try any of the following methods
  5. Priority should be given to reducing super sampling, and then a smaller Angle of view should be adopted to set pitool’s picture quality level lower and the refresh rate lower. Finally, pay attention to restart the helmet, otherwise the setting is invalid and some of them need to be applied
  6. Note: because pettitte’s helmet has a large viewing Angle, high resolution and high graphics card pressure, so don’t overdo it blindly. 2560x1440 is recommended for 5k helmet (the single-eye resolution is the same as that of 5k helmet)


Six, the simplest method to restart the helmet, reduce the error rate after restart

  1. Many of the above Settings need to restart the helmet, otherwise the Settings are invalid. The easiest way to restart the helmet is to click the room Settings
  2. After clicking the room setting, the helmet will be forced to restart, and then the room setting will be turned off immediately

    Seven, improve pettitte’s resolution, especially for 8k players
    Steam locks the upper resolution 4k, you need to open the path C:\Program Files (x86)\ steam \steamapps\common\SteamVR\resources\ Settings \default. Vrsettings
    Use your notepad to open default.vrsettings, then maxRecommendedResolution": 4096, amend this 4096 to 8192, then save the text
    Uploading: 4.jpg…

小派vr头盔高级使用手册 2020.4.25
注意:我的文档都有图片,只能登陆电脑qq才可见
一,减少黑暗场景时的泛白情况,调节对比度、亮度
1,对比度只选1,亮度-3 -2 -1都行,太黑就亮度-1,选好点应用,重启头盔
2,oled的小派5k xr有黑色等级选项,可进一步减少泛白情况,lcd的小派没有

二,画面不重叠、显示异常,需要打开平行投影
1,打钩“兼容使用平行投影”,调整选择小视角,重启头盔
2,注意最大视角开平行投影,极为影响画质,小视角则没有影响,平常别开平行投影

三,头盔无法识别,手柄却能识别,怎么办?
1,手持头盔,在两个基站之间反复大幅度摇晃,大约15秒即可
2,游戏时头盔丢失信号,也可用这个办法,游戏进度不会丢失

四,头盔完全无法识别,手柄也无法识别,怎么办?
1,直接卸载pitool,关闭360,重新安装pitool,一般立刻恢复正常
2,若重装后还是不行,重启电脑并重复步骤1

五,画面出现畸变、卡顿,甚至拖影,怎么办?
1,出现上述问题,说明游戏优化差、或显卡配置不够、或超级采样拉太高,你可选尝试下面任何办法
2,优先降低超级采样、其次用更小的视角、设置pitool的画质等级更低、选更低的刷新率,最后注意重启头盔,否则设置无效,有的还要点应用
3,注意:因为小派头盔视角大、分辨率高、显卡压力大,所以不要瞎拉超采,5k头盔 推荐2560x1440(和5k头盔的单眼分辨率一致),在此基础上酌情增加,加太多意义不大,画质提升有限,显卡压力却暴增,导致画面卡顿、掉帧

六,最简单的重启头盔方法,减少重启后的报错率
1,上述很多设置,都需重启头盔,否则设置无效,而重启头盔最简单方法是点击房间设置
2,点房间设置后,就代表头盔强制重启了,然后立刻关闭房间设置即可

七,提升小派的分辨率,尤其是8k玩家
steam锁死了分辨率上限4k,你需要打开路径C:\Program Files (x86)\Steam\steamapps\common\SteamVR\resources\settings\default.vrsettings
用记事本打开default.vrsettings,然后将maxRecommendedResolution": 4096,这个4096修改为8192,然后保存文本